how to test mass air flow sensor chevy silverado

The hood release is located under the dashboard on the drivers side. On this episode of Fear No Fix Jim and Chris replace the Mass Airflow Sensor MAF in a 53L Chevrolet Silverado model years 1999-2006Need help diagnosi.

Map Sensor Wiring Diagram Map Sensor Automotive Repair Auto Repair

No scan tool is required or any other expensive testing equipment.

. Unplug the electrical connector from the mass airflow sensor. Find the location of the MAF sensor in your Silverado HD it will be somewhere between the air filter box and the throttle body. The mass airflow sensor commonly abbreviated to MAF is one of the most important engine management sensors.

Now use the airflow cleaner to spray the plate and clean them. Remove the screws that hold the mass airflow sensor in place. On top of the sensor you can see a harness connector situated next to the sensor module.

Check if this part fits your vehicle. 1 How does a MAF sensor work. You just want to push the tab on the bottom of that connector and pull it free and then remove the two T15 screws on either side of the airflow sensor.

To detach the connector push down on the tabs and pull it straight out. However you should be careful to not scrub the parts as this might end up breaking or damaging the wire. Spray at least 10 spurts of MAF cleaner onto the sensor and then let it air dry for an hour or until completely dry.

10 Easy Steps to. Furthermore detach the connection between the electric connector. Your mass airflow sensor is right here on this air intake hose.

The following test is an on-car test that checks the performance of the MAF sensor with the engine running. Youll test this GM MAF sensor with a multimeter that can read Hertz Hz frequency. Make sure you dry the MAF sensor before fitting it back to the car in the air duct.

Chevy Mass Air Flow MAF Sensor Replacement Guide. Vehicle Stuck in Limp Mode Problems How to reset. Replacing an ABS wheel speed sensor on a Chevy or GMC vehicle is an easy and simple procedure that can be performed at home with basic tools.

Without knowing how much air is really getting into the engine P0101 will be thrown. However remember the wire or plates are delicate so avoid rubbing or scrubbing them. Clean your dirty mass air sensor.

Chevrolet Silverado 1500 Mass Air Flow Sensor Standard Ignition Mass Air Flow Sensor New - Standard Ignition This Listing Sells 1 Part. Buy Chevrolet Silverado 1500 Mass Air Flow Sensor online and get Free Next Day Delivery on qualified purchases or pick up your parts at a nearby AutoZone today. 2 How To Clean Mass Air Flow Sensor Chevy Silverado 2004-2006 21 Step 1.

Remove the sensor from the housing. Intake ManifoldVacuum Leak If there is a leak in the intake manifold it will be impossible for the MAF sensor to get an accurate reading. Reinstall and test drive.

It acts like it is running on 6 cylinders and when I unp. Then disconnect the electrical connector and spray 10 to 15 spurts of the cleaner onto the wireplate. It passes this information onto your Silverados ECU.

A bad mass air flow sensor will usually trigger a check engine light. Unplug the electrical connector. Check Engine Light appearing on the dashboard.

Press the red clip slightly to unlock it. For GMC Sierra 3500 HD Mass Air Flow SensorProbe Only Delphi. Thankfully the air filter is able to remove most of the dirt and debris that can get into the mass air flow sensor.

Cleaning the mass air flow sensor on your Silverado is extremely simple. Here are some of the most common bad mass air flow symptoms that you will typically come across. Find the location of the MAF sensor in your Silverado 1500 it will be somewhere between the air filter box and the throttle body.

You will need to feel this out and check to see how long it takes for yours to get dirty. Spray at least 10 spurts of MAF cleaner onto the sensor and then let it air dry for an hour or until completely dry. Locate and disconnect the MAF sensor.

A MAF sensor measures the density of the air entering the intake manifold. I find it hard to believe both ca. The MAF sensor is located between the air filter housing and air inlet hose.

Therefore the most common signs of a bad mass air flow sensor usually appear in the form of an engine that is performing badly. A bad mass airflow sensor can leave your Chevy Silverados engine running rough or even inoperable. A dirty mass air flow sensor can be frustrating to drive.

3 Symptoms of a Faulty Mass Air Flow Sensor. Remove the entire air mass sensor. This important part of the trucks engine controls the amount of fuel that can be delivered to the engine.

Unplug the electrical connector. Once removed the sensor just lifts right up and out. You will need to remove the sensor from the intake and spray it down with appropriate cleaners.

Ecmmass air flow sensor6 cylinderspassenger side I have a 2003 chevy silverado. Its not running right my mechanic says the ecm is is bad but the dealer said the mass air flow sensor was bad. 2006 Chevy Silverado wiring diagram 593.

The air-to-fuel ratio is one of the critical factors in determining the power and efficiency of your Silverados engine. MAF Sensor Wiring Make sure to check around the MAF sensor for opens or shorts. This is one of the easiest mass air flow sensors to test.

First remove your mass airflow sensor from the air tube or pipe very carefully. Remove the sensor from the housing. Open the hood of your Chevrolet.

MAF sensor location between the air filter housing and inlet tube. Locate the mass airflow sensor near the engine air filter housing.

Pin On Auta